Front panel: black glass and anodized gold/silver. Panloc buttons for the device installation on shelf.
From left to right. Upper level: Balance – Input selector (Aux/Tape/Tuner 2/ Tuner 1/Phono 1 /Phono 2/Mic/Tape HD) – Mode selector (L to L&R/R to L&R/Stereo Rev/Stereo/Mono L+R/L+R to L/L+R to R) – Volume. Lower level: Bass controls (Left channel/Right channel) – Comp[ensation](RIAA/LP) – Tape (Normal/Monitor) – Power (On/Off) – Left tape jack input – Tape jack switch (Record/Playback) – Right tape jack input -Rumble filter – HF filter – Loudness – Treble controls (Left/Right)
Pannello frontale in vetro nero e anodizzato oro/argento. Pulsanti PANLOC necessari per l’installazione dell’apparecchio su di una mensola.
Da sinistra a destra. Livello superiore: Balance – Input selector (Aux/Tape/Tuner 2/ Tuner 1/Phono 1 /Phono 2/Mic/Tape HD) – Mode selector (L to L&R/R to L&R/Stereo Rev/Stereo/Mono L+R/L+R to L/L+R to R) – Volume. Livello inferiore: Controllo Bassi (Left channel/Right channel) – Comp[ensation](RIAA/LP) – Tape (Normal/Monitor) – Power (On/Off) – Left tape jack input – Tape jack switch (Record/Playback) – Right tape jack input -Rumble filter – HF filter – Loudness – Controllo alti (Left/Right)
Back panel. From left to right. Upper level: AC outlet (4 switched, 660w total) – Outputs (Mono L+R/ Main/Tape) – High level inputs (Tape minitor/Aux/Tape/Tuner 1/Tuner 2) Low level inputs (Phono 1/Phono 2/Mic/Tape Head). Lower level: AC outlet (Unswitched) – Fuse – From power amp to speaker connections – Tube access door.
Pannello posteriore.Da sinistra a destra. Livello superiore: AC outlet (n.4, dipendenti, 660w totali) – Uscite (Mono L+R/ Main/Tape) – High level inputs (Tape monitor/Aux/Tape/Tuner 1/Tuner 2) Low level inputs (Phono 1/Phono 2/Mic/Tape Head). Lower level: AC outlet (Indipendente) – Fusibile – Connessioni fra finale e diffusori – Porta di accesso al vano valvole.
TOP PANEL FACILITIES
“Depressing the Panloc buttons allows the C22 to slide forward to a point approximately 3 inches from the mounting panel. In this position, additional controls on the top of the C22 chassis are available.” [from left to right]:
TAPE EQUALISATION [Left/Right channel]. To compesate for 3% tape speed.. set NAB for normal 7.5 inch tape speed machines. Turning tha Tape equalisation controls clockwise increases the treble response; turning them coun terclockwise descreases treble response.
LOW FREQUENCY TRIM [Left/Right channel]. .to adjust for un equal speaker response at low frequencies due to room location of speakers. Approximately 6 dB of boost below 100 cycles is available.
OUTPUT LEVEL [Left/ Left + Right /Right] .. to balance the overall amplifier-speaker system. The minimum setting on each control reduces the output level approximately 15 dB. The L+R (left+right) control adjusts only theoutput from the L+R output jack [of the back panel]
PHASE (Reverse 180°/Normal 0°) [backwards]
PILOT LAMP (Dim/Bright) [forwards]
[from the Owner’s manual]
COMANDI DEL PANNELLO SUPERIORE
“La pressione dei pulsanti Panloc consente al C22 di scorrere in avanti fino a un punto a circa 3 pollici dal pannello di montaggio. In questa posizione, sono disponibili controlli aggiuntivi sulla parte superiore del telaio del C22.” [da sinistra a destra]:
EQUALIZZAZIONE DEL NASTRO [Canale sinistro/destro]. Serve per compensare la velocità del nastro del 3%.. impostare NAB per normali macchine con velocità del nastro da 7,5 pollici. Ruotando i controlli di equalizzazione del nastro in senso orario si aumenta la risposta degli acuti; ruotandoli in senso antiorario si diminuisce la risposta degli acuti.
TRIM BASSA FREQUENZA [Canale sinistro/destro] Serve per regolare una risposta dei diffusori non uniforme alle basse frequenze a causa della posizione dei diffusori nella stanza. Sono disponibili circa 6 dB di aumento al di sotto dei 100 cicli [Herz].
OUTPUT LEVEL [Left/ Left + Right/ Right] Serve per bilanciare l’intero sistema amplificatore-altoparlanti. L’impostazione minima su ciascun controllo riduce il livello di uscita di circa 15 dB. Il controllo L+R (sinistra+destra) regola solo l’uscita dal jack di uscita L+R [presente sul pannello posteriore]
PHASE (Inversione 180°/Normale 0°) [posto più indietro]
LAMPADE PILOTA (Diminuite/Più Luminose) [posto più avanti]
[dal manuale di utilizzo]
TUBES
6 each 12AX7
SPECIFICATIONS
Power requirement: 117 Volts 50/60 cps AC, 34 watts
Input sensitivity and Impedance – Aux,Tape,Tuner 1 and 2: 0.25 volts, 250 kohms – Phono 1 and 2: 2 mV,47kohms – Mic: 2.5 mV, 1 megaohm – Tape head: 2mV, 1 megaohm – Tape compare: 0.25 volts,25 kohms
Frequency response: ± 0.5 dB from 20 cps to 20,000 cps
Distortion: less than 0.2% at 10 volts output – Less than .02% at 3 volts output.
Total noise – High level inputs: 85dB below rated output. Low level input: Less than 1.5 microvolts at input terminals.
Main Output: 2.5 volt with rated input.
Tape Output: 0.25 volts with rated input
Left + Right Output: 1 volt from generator impedance of 25,000 ohms.
Available on request:
- the Owner’s manual
- the Service manual
- Schamatics
SPECIFICHE
Alimentazione e consumo: 117 Volts 50/60 cps AC, 34 watt
Sensibilità e Impedenza – Aux,Tape,Tuner 1- 2: 0.25 volts, 250 kOhms – Phono 1-2: 2 mV,47kOhms – Mic: 2.5 mV, 1 megaOhm – Tape head: 2mV, 1 megaOhm – Tape compare: 0.25 volts,25 kOhms
Risposta in frequenza: ± 0.5 dB from 20 Hz to 20,000 Hz
Distortion: meno di 0.2% a 10 volt in uscita – meno di 0.02% a 3 volt in uscita.
Rumore totale – Ingressi di alto livello: 85dB entro il valore di uscita dichiarato. Ingressi basso livello: meno di 1.5 microvolt ai terminali di ingresso.
Uscita principale: 2.5 volt con il valore di ingresso dichiarato.
Uscita Tape: 0.25 volt con il valore di ingresso dichiarato.
Uscita Left + Right: 1 volt dal generatore di impedenza di 25.000 Ohm.
Disponibili a richiesta:
- il manuale di utilizzo
- il manuale di servizio
- gli schemi
C-22 Reissue or Commemorative Edition (C.E.)
Commemorative issue preamplifier dedicated in memory of the late Frank H. McIntosh, founder of McIntosh Laboratory and its president from 1949 (the Company inception) to 1977 (when he retired).
Front panel in anodized gold/silver and black glass. From left to right. Upper level: Balance – Input selector (tape 2/tape 1/CD/tuner/phono 1/phono 2/aux 1/aux 2) – Mode selector (L to L&R/ R to L&R/ Stereo Reverse/ Stereo/ Mono L+R/L+R to L/ L+R to R) – Volume. Lower level: Bass controls (Left/Right) – Tape 1 (Normal/Monitor) – Tape 2 (Normal/Monitor) – Power (On/Off) – Aux 2 Input jack – Speaker selector (Off/1/2/1+2) – Headphones input jack – Rumble filter – HF filter – Loudness – Treble controls (Left/Right).
Modello commemorativo dedicato alla memoria dell’ultimo Frank H. McIntosh, fondatore della McIntosh Laboratory e suo presidente dal 1949 (anno della fondazione della compagnia) fino al 1977 (quando egli si ritirò in pensione).
Pannello frontale in anodizzato oro/argento e cristallo nero. Da sinistra a destra. Livello superiore:Balance – Selettore ingresso (tape 2/tape 1/CD/tuner/phono 1/phono 2/aux 1/aux 2) – Selettore Modo (L to L&R/ R to L&R/ Stereo Reverse/ Stereo/ Mono L+R/L+R to L/ L+R to R) – Volume. Livello inferiore: Controllo bassi (Left/Right) – Tape 1 (Normal/Monitor) – Tape 2 (Normal/Monitor) – Power (On/Off) – Aux 2 Ingresso jack – Selettore Speaker (Off/1/2/1+2) – Ingresso jack cuffia – Filtro Rumble – Filtro HF – Loudness – Controllo alti (Left/Right).
Back panel. From left to right.Upper level: AC outlets (4 switched) – Outputs (Switched 1/Switched 2/Main/Tape 2/Tape 1) – High level inputs (Aux 1/Tape 2/ Tape 1/CD/Tuner) – Ground binding post – Low level inputs (Phono 1/Phono 2). Lower level: AC outlet (1 unswitched) – Balanced tripolar outputs (Left/Right) – SCR input – Tube door access.
AC Outlets
The AC outlets have a maximum total rating of 1400 watts (11.6 amperes). The Switched 1 and 2 may be connected to the inputs of power amplifier. These two outputs turn on only with the front panel speaker switch. You can turn on either pair of output independently, or both simultaneosly. The balanced outputs allow the connection with cables XLR to the balanced input jacks of the power amplifier. Using balanced connnectors and cables can reduce noise and interference by as much as 40dB. If cable lenghts between the C22 and the power amplifier are short (one meter or less), you will probably find high quality unbalanced cables to be equallly satisfactory. The SCR input allows connection with TV or PC.
Pannello posteriore. Da sinistra a destra. Livello superiore: Prese ausiliarie (4 dipendenti) – Uscite (Switched 1/Switched 2/Main/Tape 2/Tape 1) – Ingressi alto livello (Aux 1/Tape 2/ Tape 1/CD/Tuner) – Ingressi basso livello (Phono 1/Phono 2) – Terra – Livello inferiore: Presa ausiliaria (1 indipendente) – Uscita tripolare bilanciata (Left/Right) – Ingresso SCR – Porta di accesso alle valvole.
Prese ausiliarie
Le prese ausiliarie hanno una potenza massima totale di 1400 watt (11.6 ampere). Le uscite Switched 1 e 2 possono essere connesse agli ingressi di amplificatore di potenza. Queste due uscite funzionano solo mediante il selettore speaker del pannello frontale. E’ possibile selezionare l’uno o l’altro paio di diffusori indipendentemente, oppure entrambi simultaneamente. Le uscite bilanciate tripolari consentono la connessione mediante cavi XLR agli ingressi bilanciati degli amplificatori di potenza. L’utilizzo dei connettori bilanciati e dei cavi adatti può ridurre il rumore e l’interferenza fino a 40 dB. Se la lunghezza dei cavi fre il C22 e l’amplificatore è breve (un metro o meno), si rileverà probabilmente che i cavi non bilanciati sono altrettanto soddisfacenti. L’ingresso SCR permette la connessione con una TV o un PC.
TUBES
“The tube complement retains the reliable 12AX7A for the amplifying stages. The cathode follower output stages are changed to 12AT7s to allow more current output to drive lower impedance loads.” [from the Owner’s manual]
(5) 12 AX7A – (2) 12AT7
VALVOLE
“La dotazione valvolare conserva l’affidabile 12AX7A per gli stadi di amplificazione. Gli stadi di uscita successivi del catodo sono stati modificati per le 12AT7, al fine di consentire un’uscita di corrente maggiore e pilotare altresì carichi di impedenza inferiori.” [dal manuale di utilizzo]
(5) 12 AX7A – (2) 12AT7
SPECIFICATIONS
Power requirements: 120V, 50/60 Hz, 37 watts
Frequency response:± 0.5 dB from 20 to 20,000 Hz
Total harmonic distortion: 0.02% maximum IHF – 0.2% maximum from 20 to 20,000 Hz at rated output.
Signal to noise ratio. phono: 80 dB below 10 mV input – High level: 90 dB below rated output.
Sensitivity. Phono 2.2 mV for rated output,(0,45 mV IH F) – High level:250 mV for 2.5 rated output (50 mV IHF)
Rated Output: 2.5V at Main, Switched 1/2 and Balanced Outputs
Maximum voltage Output: more than 8V at all outputs.
Voltage gain. Phone to tape: 41dB at 1000 Hz – Phono to Main 61 dB at 1000 Hz – High level to tape: 0 dB – High level to main: 20 dB
Dimensions: 16″ (40,6 cm) Wide x 5 7/16″ (13.8 cm) High – 14″ (35.6 cm) Deep
Weight: 18 lbs (8,2 Kg)
SPECIFICHE
Alimentazione e consumo: 120V, 50/60 Hz, 37 watts
Risposta in frequenza:± 0.5 dB da 20 a 20.000 Hz
Distorsione armonica totale; 0.02% max in IHF – 0.2% max da 20 to 20.000 Hz alla potenza dichiarata.
Rapporto segnale rumore. Phono: 80 dB entro 10 mV in ingresso – Alto livello: 90 dB entro la potenza dichiarata.
Sensibilità. Phono 2.2 mV per potenza nominale,(0,45 mV IH F) – Alto livello: 250 mV per 2.5 potenza nominale(50 mV IHF)
Potenza nominale: 2.5V su le uscite Main, Switched 1/2 and Balanced Outputs
Voltaggio massimo in uscita: superiore a 8V in tutte le uscite.
Guadagno di Voltaggio: Phone to tape: 41dB at 1000 Hz – Phono to Main 61 dB at 1000 Hz – High level to tape: 0 dB – High level to main: 20 dB
Dimensioni: 16″ (40,6 cm) larghezza x 5 7/16″ (13.8 cm) Altezza – 14″ (35.6 cm) Profonfdità
Peso : 18 lbs (8,2 Kg)
McIntosh C22 vs McIntosh C22 C.E.
| C22 | C22 C.E. (Reissue) | |
|---|---|---|
| Power requirement | 117V,50-60 Hz, 34W | 120V,50-60 Hz, 37w |
| Frequency Response | +0, -0.5 dB (20-20,000) cps | +0, -0.5 dB (20-20,000) cps |
| Total Harmonic Distortion | Less than 0.2% at 10V output Less than 0.02 at 3V output | 0.02% max IHF 0.2% max 20-20,000 Hz [at rated output] |
| Sensitivity & Impedance | Aux,Tape,Tuner 1/2: 0.25V Phono 1/2: 2 mV, 47 khoms Mic:2.5 mV,1 MOhm Tape head: 2 mV,1Mohm Tape compare:0.25V,25 kohms | High level: 250 mV for 2.5V at rated output Phono:2.2 mV for 2.5V @ rated output |
| Signal to Noise Ratio | Low level input: less than 1.5 microvolts at input terminals High level input: 85 dB below rated output | Phono 80 dB below 10 mV input High level: 90 dB below rated output |
| Rated Output | Main: 2.5V (rated input) Tape: 0.25V (rated input) Left+Right:1V (generator 25kohms | Main/Switched 1,2/Balanced outputs: 2.5V |
| Voltage Gain | Aux-Tape-Tuner 1,2: 20 dB (to main) Phono 1,2: 62 dB (to main) Mic:60 dB (to main) Tape head (@500 cps): 62 dB | High level to main: 20 dB Phono to main: 61 dB at 1000 Hz |
Are availailable on request:
- the Owner’s manual
- the Service manual
- Schematics
Sono disponibili a richiesta:
- il manuale di utilizzo
- il manuale di servizio
- gli schemi